Highland Village, Euless

Garage Door Service for Highland Village's 1990s-Era Doors

Highland Village homes went up mostly around 1993 - torsion hardware sized for heavier steel doors. Euless Garage Door Pros travels 17 miles to service them.

(817) 985-1262 Request a quote

A technician in black gloves sprays lubricant on a white garage door hinge.

On the truck

Parts We Carry

A door built around 1993, which is the median year for this area, is almost always a steel sectional on torsion springs rated for a heavier panel than the aluminum doors that came before it.

Sizes differ from older doors

That means the springs, drums, and cables on a Highland Village door are a different size than what you'd pull off a house from the 1960s or 70s.

Stocked springs and rollers

We stock torsion springs in the ranges common to that era, along with steel rollers (nylon if the household wants quieter), standard lift cables, and center and end bearing plates.

Ordered proprietary parts

What we don't keep on the truck is anything proprietary to a specific opener brand's circuit board or a custom-sized panel - those get ordered, and that can add a few days depending on the manufacturer. If your door was replaced more recently than the house, tell us the brand and age when you call; it changes what we bring.

DIY or pro

The DIY Question

A torsion spring holds real tension, and on a double-wide steel door from the early 90s that tension is higher than people expect because the door itself is heavier than older wood or single-layer aluminum doors. We don't recommend winding or replacing torsion springs yourself. Rollers, weatherstripping, and tightening loose hardware are reasonable DIY jobs. Realigning a track that's come off its mounts, or diagnosing why an opener runs but the door won't move, usually needs someone who's seen the fault before - on a door this age, a motor that strains is as often a dying spring as a dying motor, and guessing wrong wastes a part.

A silver van is parked in a driveway in front of a black garage door.

Booking

Getting It Booked In

A house with a beige garage door, brick and stone siding, and pink flowering trees.

We run out of Euless, about 17 miles away, so when you call we're scheduling a trip out rather than dispatching from a local yard. Tell us the door's approximate age (1993 is the median build year here, but plenty of homes are newer or older) and what it's doing - grinding, off-track, won't close - so we bring the right spring size and hardware the first time instead of making a return trip. We don't hold a standing crew in Highland Village itself, so booking ahead works better than hoping for a same-day slot.

Local causes

Why This Fails Locally

A house with a brown garage door and brick exterior is seen from the street.

This area sits in a severe-heat climate band, and steel doors from the early-to-mid 90s weren't built with the insulation or expansion tolerances that newer doors have. Summer heat cycles cause the steel to expand and contract daily, which over three decades works springs and hardware harder than a mild climate would. On a door built new in 1993, that's roughly thirty summers of thermal stress on the same spring and the same bearing plates, which is a big part of why we see original torsion springs failing on these houses now rather than on the newer builds nearby.

Watch-outs

What Can Go Wrong

On houses built close to the 1993 median, the most common calls we get are torsion springs that have finally worn past their cycle life, rollers that have hardened and started chipping (nylon rollers from that era weren't built to last three decades), and center bearing plates that have worn an oval groove into the shaft.

Original opener gear failures

A smaller share are openers original to the house - by now most have been replaced once, but the ones that haven't tend to fail at the gear or the circuit board rather than the motor itself.

Strut issues, not springs

We also see double-wide doors sagging slightly at the bottom corners, which is a strut issue more than a spring issue, and worth mentioning separately because fixing the spring won't fix that sag.

Timing

How Long It Takes

A straightforward torsion spring replacement on a standard double door usually runs under two hours once we're on site with the right spring. Roller or cable work is quicker. Opener replacement adds time for mounting and programming, more if the old unit was hardwired into a chain-drive setup from the 90s that needs new rail hardware. We won't quote arrival time from Euless over the phone - traffic on the drive out varies - but once we're there, most single-fault jobs on a house this age are a same-visit fix, parts on the truck permitting.

A single-story brick house with a beige garage door and a large tree in the yard.

Questions

Common questions

How far out does Euless Garage Door Pros travel for Highland Village?

About 17 miles from our Euless base. We don't keep a branch or stocked vehicle in Highland Village, so we schedule the trip when you call rather than dispatching locally - tell us your door's age and symptom up front so we bring the right parts.

Why do so many houses here need springs replaced around the same age?

Most homes in this area were built around 1993, so their original torsion springs are hitting the end of their cycle life at roughly the same time, and three decades of severe summer heat cycling adds extra wear on top of normal use.

Is it worth replacing the whole door instead of just fixing the spring?

If the spring is the only issue and the panels and track are sound, a spring swap is the cheaper and faster fix. Replacement makes more sense when the steel panels have rusted through or the door is sagging badly at the struts - we'll tell you honestly which situation you're in.

Explore more